Navigate to the STI Vibration Monitoring Inc. homepage

-
You are here: Home > 4-20mA Output Sensors > Velocity Output
The loop powered 4-20 mA output sensors are designed to interface directly to an analog input card on a Control System (PLC or DCS). The 4-20 mA output is proportional to the full-scale range in terms of Velocity and is capable of transmitting signals over a long distance without signal loss.

Loop-Powered Velocity Transmitters From STI Vibration Monitoring
Loop-powered 4-20 mA Output Sensors are designed to measure the overall machine vibration accurately and reliably in terms of Velocity. What sets loop-powered velocity transmitters apart is that the accelerometer and transmitter are built-in, eliminating the need for an external transmitter. This not only simplifies installation and reduces costs, but it also makes these transmitters ideal for Low-Cost Condition Monitoring Systems.
With their advanced technology and unparalleled performance, loop-powered velocity transmitters from STI Vibration Monitoring are an essential tool for industries such as oil and gas, chemical processing, and power generation. Choose STI Vibration Monitoring for efficient and effortless velocity measurement with loop-powered velocity transmitters. Place your order today.
Click on the image below to view the product page.

Choose a sub category:

MS Connector
Integral Cable
M12 Connector
Terminal Block

Velocity Output

MS Connector
Integral Cable
M12 Connector
Terminal Block
    CMCP420VT Loop-Powered Vibration Transmitter Vibration Analysis Equipment

    CMCP420VT Top Exit, with Dynamic Output

    • 4-20mA Output in Velocity RMS (in/s or mm/s)
    • 100mV/g Dynamic Output
    • 3/4" NPT Conduit Fitting Connection
    • Screw Terminal for Direct Wiring
    • 2 Hz to 2 kHz Frequency Response
    • Class 1 Division 2 Approved
    • Optional Integral Display
    $440.00
    Select Options
    Top Exit MS 2 Pin 5015 Connector Transmitter Vibration Analysis Equipment

    CMCP422VT-C Top Exit, MS Connector

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Top Entry MS Connector
    • Class 1 Division 1 and 2 Approved
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $240.00
    Select Options
    Velocity Transmitter, Top Exit with Integral Braided Cable Vibration Analysis Equipment

    CMCP422VT-I Top Exit, Armored Cable

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Top Entry, Integral Armored Cable
    • Class 1 Division 1 and 2 Approved
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $240.00
    Select Options
    Top Exit MS PUR Submersible Accelerometer Vibration Monitoring Equipment

    CMCP422VT-IP Top Exit, Submersible

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Top Entry, Submersible Integral Cable
    • Class 1 Division 1 and 2 Approved
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $240.00
    Select Options
    Top Exit M12 4 Pin Connector Transmitter Vibration Analysis Equipment

    CMCP422VT-M12 Top Exit, M12 Connector

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Top Entry M12 Connector
    • Class 1 Division 1 and 2 Approved
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $240.00
    Select Options
    Side Exit MS 2 Pin 5015 Connenctor Transmitter

    CMCP422VTS-C Side Exit, MS Connector

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Side Entry, MS Connector
    • Sealed to IP68 (or IP67 with M12 Connector)
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $275.00
    Select Options
    Velocity Transmitter, Side Exit with Integral Braided Cable

    CMCP422VTS-I Side Exit, Armored Cable

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Side Entry Low Profile
    • Armored Integral Cable
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $275.00
    Select Options
    Submersible Vibration Transmitter

    CMCP422VTS-IP Side Exit, Submersible

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Side Entry Low Profile
    • IP68 Submersible Integral Cable
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $275.00
    Select Options
    Side Exit M12 4 Pin Connector Transmitter

    CMCP422VTS-M12 Side Exit, M12 Connector

    • 4-20mA Output in Velocity (in/s or mm/s)
    • RMS or Peak Detection
    • Side Entry, M12 Connector
    • Sealed to IP68
    • 10 Hz to 1 kHz Frequency Response
    • -25 to +120°C Operating Temperature
    • Two Wire Operation
    • Lifetime Warranty
    $275.00
    Select Options

Get access to the latest deals and more!

Empty Cart